Airplane Hand Plane - Powerful Handmade site

Airplane Hand Plane

Sharing is caring!

Introduction: Airplane Hand Plane

Airplane Hand Plane

Show All Items

This Airplane Hand Plane is constructed from mahogany and maple. It’s an ideal wooden store show piece, plus it in fact works and makes shavings too! This can be a a laugh starter aircraft for youngsters. Watch my video to peer how I made it, then click on right here to obtain the templates from my weblog.

Step 1: Print Out the Templates.

Print Out the Templates.

Show All Items

Click right here to learn my weblog publish the place you’ll obtain my templates. Print the templates at precise measurement on Legal eight.five”x14″ paper.

Step 2: Cut the Two Sides and Drill the Holes.

Cut the Two Sides and Drill the Holes.
i05.jpg

Show All Items

Attach the facet templates for your board and minimize them out. Drill the holes for the plane home windows and the blade pin. I used 1/four” maple for the edges.

Step three: Make the Middle of the Fuselage.

Make the Middle of the Fuselage.
i06.jpg

Show All Items

I borrowed a 1.five” broad blade from an previous hand aircraft, so I minimize two items of three/four” mahogany and fixed them in combination to make the center a part of the fuselage. You will need this piece to be the similar width because the blade. Cut this center piece alongside the 45 deg and 60 deg strains, and save the wedge cutout for later.

Note: You do not have to make use of an actual blade. You could make a pretend blade out of a skinny piece of wooden to show it right into a toy aircraft for youngsters.

Step four: Assemble the Fuselage.

Assemble the Fuselage.
i08.jpg
i16.jpg

Show All Items

Use mineral spirits to take away the paper templates from the items and wipe off any spray adhesive residue. Glue the edges and the center in combination lining them up sparsely. Use a skinny layer of glue to keep away from it squeezing into the home windows and making a large number. Once the fuselage is dry, you’ll glue within the 1/2″ dowel blade pin and sand it even with the edges. It’s a lot more uncomplicated to sand this meeting now ahead of striking the wings on.

Step five: Cut and Attach the Wings.

Cut and Attach the Wings.
i10.jpg
i11.jpg

Show All Items

I minimize one each and every of the massive and small wings from the three/four” mahogany board, then re-sawed them in part to make two of each and every wing measurement. They ended up being about three/eight” thick. I set my sander desk to a slight perspective and sanded the threshold in order that the wing can be glued onto the fuselage at a quite upward perspective. Glue the wings on ensuring they’re symmetrical.

Tip! Attach the wing templates to the board in order that the threshold that might be glued to the aircraft is at the facet of the board. This lengthy grain will supply a more potent glue joint, than the top grain.

Step 6: Apply a Finish.

Apply a Finish.

Show All Items

Clean up any glue squeeze out with a chisel and sand all surfaces clean. Apply your end of selection. I sprayed my aircraft with transparent gloss lacquer to handle the wooden’s herbal colour.

Step 7: Cut the Wedge and Install the Blade.

Cut the Wedge and Install the Blade.
i14.jpg

Show All Items

Cut the wedge that can dangle within the blade. I used the cut-out piece from the center fuselage section. It was once small, so I taped it to a bigger piece to make it more secure to chop at the bandsaw. The wedge must be thick sufficient to squeeze between the pin and the blade, however now not backside out. Apply some end to the wedge piece too. Tap it in with a hammer.

Note! You shouldn’t have to make use of an actual blade. I additionally made a pretend wood blade from a skinny piece of wooden in order that children of every age can safely deal with the aircraft and test it out.

Step eight: Make Some Shavings!

Make Some Shavings!

Show All Items

If you used an actual blade, attempt to make some shavings from a skinny piece of soppy wooden like pine. I used to be in a position to make some great shavings with mine. It labored simply in addition to the previous aircraft I borrowed the blade from. If you are making such a, please ship me an image as a result of I would really like to peer it. I’m hoping those directions have been useful. Like maximum DIY initiatives, you are going to maximum like simply must “wing it”! :o)

Facebook Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

403 Forbidden

403 Forbidden


nginx
shares